Search The WebThis Site for

VALVES

If you cannot download the brochures linked below,
or if you would like further information,
you can receive product literature via postal mail.
Please phone Craig Moore at 716-667-0714.

Manufacturer Crispin

Sewer pressure air release valve

Model No: SL Series

Media: Gas. Power: Pneumatic.
Email Craig Moore for detailed product information, phone 716-667-0714.

Manufacturer Crispin

Rubber flapper check valve

Model No.: RF Series. Structure: Check.
Email Craig Moore for detailed product information, phone 716-667-0714.

Manufacturer Crispin

Tilting disc check valve

Model No. TD series. Structure: Check
Email Craig Moore for detailed product information, phone 716-667-0714.

Manufacturer Crispin

Swing check valve

Model No. SWC and SWL
Email Craig Moore for detailed product information, phone 716-667-0714.

Manufacturer Crispin

Air and vacuum valve

Model No: A and AL Series. Pressure: Vacuum
Email Craig Moore for detailed product information, phone 716-667-0714.

Manufacturer EFI - Engineered Fluid, Inc.

Control Valve Stations

Buried Capsules or Above Ground Structures
Completely pre-assembled & tested
Traffic loaded designs
Various kinds of hydraulic & electrical controls
Controlled environment actuated valves are used
SCADA compatible
Flow control, level control, pressure reducing & pressure sustaining functions.

Includes altitude valve stations, pressure reducing stations, and master meter stations.
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer EFI - Engineered Fluid, Inc.

Altitude Valve Stations

Altitude (tank level) control stations use various valves and electrical/electronic controls to allow water to move into a storage tank to precise levels and at predictable flow rates while controlling system gradient at the tank inlet. Telemetry is a significant aspect of modern, multi-tank systems where level control is a factor in water quality and efficient water use.

The below ground, seal welded steel capsules will maintain a clean, hospitable, well lit and safe environment for personnel and sensitive equipment.
Click for detailed product information, or email Craig Moore , phone 716-667-0714.
 

Manufacturer EFI - Engineered Fluid, Inc.

Pressure Reducing Valve Stations

Pressure Reducing, Back Pressure Sustaining and Flow Control stations are configured to facilitate pressure and flow control in a portion of a distribution system; such stations are used to create individual pressure zones while allowing movement of water between zones under special demand circumstances. Multiple functions can be built into the same station.
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer EFI - Engineered Fluid, Inc.

Master Meter Stations

Master Meter Stations come in numerous configurations using various kinds of mechanical and electronic meters for both transmitting information to SCADA or for billing custody exchange. Meter stations can include pressure and flow control valves and can include bi-directional metering for use between users or zones. Meter accuracy is closely controlled in the design by properly matching meter straight-run requirements.
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

HP350

Available in sizes 6 through 48 inches
ANSI 250# with 250 drilling
350 psi
525 shell test
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

HP250I™

Available in sizes 3"-20" Bonded Seat
Available in sizes 24"-48" E-Lok Seat
AWWA Class 250B
Ductile Iron Valve Body and Disc
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

2FII Bonded Seat Butterfly Valve

Available in sizes 3 through 20 inches
Conforms to AWWA C504, Class 150B
Bonded seat -in-body
Manual, Cylinder and Motor Actuation
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

MKII Butterfly Valve

Available in sizes 3 through 20 inches
Conforms to AWWA C504, Class 150B
Wafer type
150 psig
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

Triton Rubber Seated Butterfly Valve

Available in sizes 24 through 162 inches
Conforms to AWWA C504
Rubber seat-in-body configuration
Available in flanged and mechanical joint ends
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

Groundhog Buried Service Rubber Seated Butterfly Valve

Available in sizes 4 though 72 inches
Meets and exceeds AWWA Standard C-504
Seat-on-body design
Available in flanged and mechanical joint ends
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

HP-250 butterfly valve, 250# flanged ends

Available in sizes 6"-48"
AWWA Class 250B
Cast Iron Valve Body/Cast Iron or Ductile Iron Disc
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

Rectangular Rubber Seated Butterfly Valves

Available in sizes 1' x 1' up to 16' x 16'
Rubber seat-in-body
Three or four sides
Weld, Flanged or Jack Bolt end configurations
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

Metal Seated Ball Valve

Available in sizes 6-48 inches
ANSI B16.1, CL.125 or CL.250
Single- or double-seated
150, 250, or 300 psig ratings
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

Rubber Seated Ball Valve

Available in sizes 4-60 inches
Conforms to AWWA C-504
Single- or double-seated
150 and 300 psi pressure ratings
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

Cone Valve

Available in sizes 8 through 48 inches
Class 125 and 250 flanges
Ductile iron body
Metal-to-metal seats
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

Ballcentric Plug Valve

Sizes 1/2" through 36
Welded nickel body seat
Cast iron valve body
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Henry Pratt Company

Multiport Plug Valve

Sizes 3" through 16
Ductile iron plug
Cast iron valve body
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Onyx Valve

Duckbill Valve: Series DBS, Slip-on Check Valve

The series DBS rubber check valve effectively ensures mono-directional flow of slurries, sewerage, sludge, and other hard to handle fluids. The valve consists of an elastomer ‘duckbill’ with a slip-on connection. This simple rugged design
eliminates the mechanical parts which can wear and jam in conventional check valves.

• Elastomer materials of construction
• Low pressure drop
• Corrosion resistant
• Frost proof
• Silent operation.

Available in a variety of elastomer compounds.

Duckbill Valve: Series DBF Flanged Check Valve

The series DBF rubber check valve effectively ensures monodirectional flow of slurries, sewerage, sludge and other hard to handle fluids.

The valve consists of an elastomer “duckbill” with a flanged connection. The back up flange is galvanized carbon steel, with 304 or 316 stainless steel as options. This simple rugged design eliminates the mechanical parts which can wear and jam in conventional check valves. They are available in a variety of elastomers.

Duckbill Valve: Series DBCP Flanged Check Valve

The series DBCP rubber check valve effectively ensures monodirectional flow of slurries, sewerage, sludge and other hard to handle fluids.

The valve consists of an elastomer duckbill with a flanged connection. The back up flange is galvanized carbon steel, with 304 or 316 stainless steel as options. This simple rugged design eliminates the mechanical parts which can wear and jam in conventional check valves. They are available in a variety of elastomers.

Duckbill Valve: Series DBRS Slip-in Check Valve

• Elastomer materials of construction
• Low pressure drop
• Corrosion resistant
• Frost proof
• Silent operation
• Available in a variety of elastomer compounds
• Stainless steel clamp bands available in 304 or 316

The series DBRS rubber check valve effectively ensures mono-directional flow of slurries, sewerage, sludge and other hard to handle fluids.

The valve consists of an elastomer duckbill that slips inside the pipe. An expanding metal band clamps the duck bill valve securely in place.

Duckbill Valve: Series DBMJ Fully Enclosed Check Valve

The series DBMJ pinch valve effectively ensures monodirectional flow of slurries, sewerage, sludge and other hard to handle fluids.

The valve consists of an elastomer ‘duckbill’ type check valve inside an iron housing. This simple rugged design eliminates the mechanical parts which can wear and jam in conventional check valves. They are available in a variety of elastomers, with a grey iron housing.

Duckbill Valve: Series DBMJ-F Fully Enclosed Check Valve

The series DBMJ-F pinch valve effectively ensures monodirectional flow of slurries, sewerage, sludge and other hard to handle fluids.

The valve consists of an elastomer ‘duckbill’ type check valve inside a steel housing. This simple rugged design eliminates mechanical parts which can wear and jam in conventional check valves. They are available in a variety of elastomer compounds, with a carbon steel fabricated housing.

Duckbill Valve: Series WCV Check Valve Wafer-Style Check Valve

The Wafer-style series WCV Check valve is an entirely new check valve design specifically engineered for water application. The WCV Check valve operates solely on line pressure and back pressure to open and close, no outside energy source is required. As line pressure builds, the elastomeric flapper disc is pushed away, allowing the water to pass. The memory of the rubber will cause the flapper disc to return flat, and back pressure will seal the flapper against the plate to prevent backflow. The WCV Check valve is designed to be inserted between two mating flanges.

Material of Construction

Flapper disc: Pure gum rubber
EPDM, Buna-N
Disc plate: Epoxy coated carbon steel (standard), 304 or 316 stainless steel (optional)

Click for detailed information on Onyx duckbill valves, or email Craig Moore , phone 716-667-0714.

Manually Operated Pinch Valve: Series CHR Full Round, Enclosed Construction, Hand Wheel Operated

Manually Operated Pinch Valve: Series CHP, Pre-Pinched, Enclosed Construction, Hand Wheel Operated

• Low pressure drop
• Linear throttling characteristic
• No packing
• Drop tight closure
• High efficiency stainless steel ACME stem for easy operation
• Available with optional limit switches
• Simple rugged cast iron construction.

Manually Operated Pinch Valve: Series DHC, Full Round, Dual Pinch, Enclosed Construction, Hand Wheel Operated

• Clog resistant full round opening
• Low pressure drop
• No packing
• Drop tight closure
• On/Off or throttling service
• Self cleaning ACME threaded stainless steel stem for easy operation.

Manually Operated Pinch Valve: Series DHA, Full Round, Dual Pinch, Enclosed Construction, Hand Wheel Operated

• Clog resistant full round opening
• Low pressure drop
• No packing
• Drop tight closure
• On/Off or throttling service
• Self cleaning ACME threaded stainless steel stem for easy operation

Manually Operated Pinch Valve: Series DHO, Full Round, Dual Pinch, Open Frame Construction, Hand Wheel Operated

• Clog resistant full round opening; valve can pass particles equal to line size
• Light weight
• Low pressure drop
• Drop tight closure
• On/Off or throttling service

Click for detailed information on Onyx manually operated pinch valves, or email Craig Moore , phone 716-667-0714.

Manufacturer Oribnox Valve

Knife Gate Valves

Ser. 10 (EX) Wafer knife gate valve (left): Application: General service (solid loaded fluids) pulp and paper, wastewater, solids, and so forth.

Sizes: 2" to 48" (DN 50 to DN 1200) Larger diameters on request.

Working pressure: 2"-10", 150 psi/DN 50-250 (10 bar)
12"-16", 90 psi/DN 300-400 (6 bar)
18", 75 psi/DN 450 (5 bar)
20"-24", 60 psi/DN 500-600 (4 bar)
28"-48", 30 psi/DN 700-1200 (2 bar)

Flange Drilling: ANSI 150, PN10, and others on request.

Ser. 20 (ET) Knife gate falve acc. to MSS SP-81(right): Application: General service (solid loaded fluids) pump and paper, wastewater, solids, and so forth.

Sizes: 2" to 30" (DN 50 to DN 750) Larger diameters on request.

Working pressure: DN 50-DN 600 (10 bar)
2"-24", 150 psi/DN 750 (7 bar)
30", 100 psi

Flange Drilling: ANSI 150, PN10, and others on request.

Ser. 30 (TL) Through conduit knife gate valve: Application: Solid loaded fluids concentration >5%) pulp, rejects, solids, and so forth.

Sizes: 2" to 32" (DN 50 to DN 800) Larger diameters on request.

Working pressure: 2"-10", 150 psi/DN 50-250 (10 bar)
12"-16", 90 psi/DN 300-400 (6 bar)
18", 75 psi/DN 450 (5 bar)
20"-24", 60 psi/DN 500-600 (4 bar)
28"-48", 30 psi/DN 700-1200 (2 bar)

Flange Drilling: ANSI 150, PN10, and others on request.

Ser. 70 (CR) Round and square part knife gate valve (left): Application: Contaminated pulp and difficult conditions (junk traps, cleaners, and so forth).

Sizes: 2" to 24" (DN 50 to DN 600)

Working pressure: 2"-24", 150 psi/DN 50-600 (10 bar)

Flange Drilling: ANSI 150, PN10, and others on request.

Ser. 80 (DT) Double gate knife gate valve (left): Application: Contaminated pulp or very high concentration (pulp, rejects, and so forth).

Sizes: 4" to 24" (DN 100 to DN 600)

Working pressure: 2"-10", 150 psi/DN 50-250 (10 bar)
12"-16", 90 psi/DN 300-400 (6 bar)
18", 75 psi/DN 450 (5 bar)
20"-24", 60 psi/DN 500-600 (4 bar)

Flange Drilling: ANSI 150, PN10, and others on request.

Ser. 11 (DT) Bi-directional knife gate valve (left): Application: General service (solid loaded fluids, wastewater, sludges, and so forth).

Sizes: 2" to 48" (DN 50 to DN 1200) Larger diameters on request.

Working pressure: 2"-10", 150 psi/DN 50-250 (10 bar)
12"-16", 90 psi/DN 300-400 (6 bar)
18", 75 psi/DN 450 (5 bar)
20"-24", 60 psi/DN 500-600 (4 bar)
28"-48:, 30 psi/DN 700-1200 (2 bar)

Flange Drilling: ANSI 150, PN10, and others on request.

Ser. 60 (VG) Rubber sleeve knife gate valve (right): Application: Abrasive slurries (mining, petrochemical, and so forth).

Sizes: 2" to 24" (DN 50 to DN 600)

Working pressure: 2"-6", 90 psi/DN 50-150 (6 bar)
8 "-10", 50 psi/DN 200-250 (5 bar)
12", 60 psi/DN 300 (4 bar)
14"-16", 45 psi/DN 350-400 (3 bar)
18"-24", 38 psi/DN 450-600 (2, 5 bar)

Flange Drilling: ANSI 150, PN10, and others on request.

Ser. 14 (VG) Hopper shape knife gate valve (left): Application: Bulk handling (powder, pellets, and so forth).

Sizes: 2" to 24" (DN 50 to DN 600) Larger diameters on request.

Working pressure: Seat opposite pressure.
2"-10", 45 psi/DN 50-250 (3 bar)
12"-16", 30 psi/DN 300-400 (2 bar)
18", 23 psi/DN 4500 (1, 5 bar)
20"-24", 15 psi/DN 500-600 (1 bar)

Flange Drilling: ANSI 150, PN10, and others on request.

Ser. 90 (BC) Square portknife gate valve (right): Application: General service (solid loaded fluids) bulk handling.

Sizes: 8" x 8" to 24" x 24" (200x200 to 600x600) others on request.

Working pressure:
8"x8", 38 psi/200x200 (2.5 bar)
10"x10" and 12"x12", 30 psi/250x250 and 300x300 (2 bar)
14"x14" and 16"x16", 23 psi/350x350 and 400x400 (1, 5 bar)
18"x18", 19 psi/450x450 (1, 25 bar)
20"x20" and 24"x24", 15 psi/500x500 and 600x600 (1 bar)

Flange Drilling: Orbinox standard, others on request.

Other Standard Valves

Ser. 35 (RM) Tilting disc check valve (at left): Application: Solid-loaded fluids, pulp and papaer, wastewater.

Sizes: 1 1/2" to 36" (DN 40 to DN 900).

Working pressure: Up to 25 bar (375 psi) depending on size.

Ser. 35 (3/4 V) 3/4 way valve (at right): Application: Pulp and paper.

Sizes: 3" to 12" (DN 80 to DN 300).

Working pressure: 10 bar (150 psi).

Ser. 35 (AT) Split body knife gate valve (at left): Application: Solid-loaded fluids, pulp and papaer, wastewater.

Sizes: 1 1/2" to 36" (DN 40 to DN 900).

Working pressure: Up to 25 bar (375 psi) depending on size.

Ser. 35 (VP) Split body knife gate valve (at right): Application: Demanding applications, bi-directional.

Sizes: 2" to 24" (DN 50 to DN 600).

Working pressure: Up to 10 bar (150 psi) depending on size.

Manufacturer Ross Valve

Relief Valve 50RWR

Sizes: 4-48
Type: Throttling
Primarily controlled by hydraulic pressure
Located in tee connection
Purpose: To prevent excessive pressure in the main line Inlet Pressure: Maximum: 300 psi
Inlet Pressure: Minimum: 5 psi
Construction: Body: 4"-36"—Cast iron (semi-steel) with bronze trim
40"-48"—Ductile iron, with bronze/stainless steel trim. (Can also be added to other basic valves as a customized feature.)
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Ross Valve

Back Pressure Sustaining Relief Valve, 50RWR

Sizes: 4-48
Type: Throttling
Primarily controlled by hydraulic pressure
Located in tee connection
Purpose: To prevent excessive pressure in the main line
Inlet Pressure: Maximum: 300 psi
Inlet Pressure: Minimum: 5 psi
Construction: Body: 4"-36"—Cast iron (semi-steel) with bronze trim
40"-48"—Ductile iron, with bronze/stainless steel trim. (Can also be added to other basic valves as a customized feature.)
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Ross Valve

Back Pressure Sustaining Relief Valve, 23RWR

Sizes: 1 1/2 - 3
Type: Direct Acting Throttling
Primarily Controlled By: Hydraulic pressure
Located: Back Pressure Sustaining: In line
Relief: In tee connection
Purpose: Back Pressure Sustaining: To prevent inlet pressure from falling below a preset minimum
Relief: To prevent excessive pressure in the main line
External Piping: None
Ends: Flanged or screwed
Inlet Pressure: Maximum: 300 psi
Inlet Pressure: Minimum: 5 psi
Class: 125 ANSI for inlet pressures to 180 psi, 250 ANSI for inlet pressures to 300 psi
Fluid: Cold water service
Construction: Cast iron body, bronze cover, pilot, piston and internal trim
Control Valves: None
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Ross Valve

Back Pressure Sustaining Relief Valve, 20WR

Sizes: 1-3
Type: Pressure positioned
Primarily Controlled By: Hydraulic pressure (upstream)
Located: Back Pressure Sustaining: In line
Relief: In tee connection
Purpose: Back Pressure Sustaining: To control inlet pressure within close tolerance
Relief: To prevent excessive pressure in the main line within close tolerance
Body Design: Angle (90 degree)
External Piping: None
End: Flanged or Female NPT
Inlet Pressure: Maximum: 1000 psi
Inlet Pressure: Minimum: 30 psi
Construction: All bronze body
Control Valves: None
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Ross Valve

Hydrant Relief Valve, 20-WR-H

Sizes: 2 1/2 hose connections
Type: Throttling
Primarily Controlled By: Hydraulic pressure
Located: Portable: Attached to a hydrant
Purpose: To protect a system that involves a hydrant from over pressure when storage is out of service
Inlet Pressure: Maximum: 350 psi
Inlet Pressure: Minimum: 5 psi
Construction: All Bronze
Control Valve: Internal Pilot: Built in
Option: Angle body design (90 degree)
Basic Application: Protect systems against excessive pressures, for example where storage is taken out of service periodically and the system is kept pressurized by a running pump and when doing maintenance on a tank.
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Ross Valve

Pressure Reducing Valve, 40WR

Sizes: 4-48
Type: Throttling
Primarily Controlled By: Hydraulic pressure
Located: In line Purpose: To prevent outlet pressure from exceeding a preset maximum level
Inlet Pressure: Maximum: 300 psi
Inlet Pressure: Minimum: 5 psi
Construction: Body: 4"-36"—Cast iron (semi-steel) with bronze trim
40"-48"—Ductile iron, with bronze/stainless steel trim
Control Devices:
Strainer: Model 5F-2
Valves: Needle
Pilot: Pressure Reducing: Model 40WR
With internal sensing port or equipped to receive a separate sensing line. (Can also be added to other basic valves as a customized feature.)
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Ross Valve

Pressure Reducing Valve, 23WR

Sizes: 1 1/2 - 3
Type: Throttling
Primarily Controlled By: Hydraulic pressure
Located: In line
Purpose: To prevent pressure from the main valve from exceeding a preset maximum level.
Ends: Female NPT or flanged
Inlet Pressure: Maximum: 300 psi
Inlet Pressure: Minimum: 20 psi
Class: 125 ANSI for inlet pressures to 180 psi
250 ANSI for inlet pressures to 300 psi
Discharge pressure: 5 psi-250 psi
Fluid: Cold water service
Construction: Cast iron body/bronze cover, pilot, piston and internal trim
Control Valves:
Orifice Pilot: Pressure Reducing: Model 23WR
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Ross Valve

Pump Control Valve, 42WS

Sizes: 2-48
Type: Nonthrottling system
Primarily Controlled By: Electricity
Located: In line
Purpose: To control surges caused by pump starting and stopping
Inlet Pressure: Maximum: 300 psi
Inlet Pressure: Minimum: 5 psi
Construction: Cast iron (semi-steel) body with bronze trim
Body: 2"-36"—Cast iron (semi-steel) with bronze trim
40"-48"—Ductile iron, with bronze/stainless steel trim
Control Devices:
Strainer: Model 5F-2
Valves:
Needle: (Closing Control)
Needle: (Opening Control)
Pilot: Solenoid: 3 Way
Other System Components:
Limit Switch: Wired to normally closed contact
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Ross Valve

Single Acting Altitude Valve, 30AWR

Sizes: 4-48
Type: Nonthrottling
Primarily Controlled By:Hydraulic pressure
Located: In line leading to storage
Purpose: To prevent elevated storage from overflowing
Band: Fixed within 9-4
Inlet Pressure: Maximum: 300 psi
Inlet Pressure: Minimum: 5 psi
Construction: Body: 4"-36"—Cast iron (semi-steel) with bronze trim
40"-48"—Ductile iron, with bronze/stainless steel trim
Plugged Tee: Incorporated in piping for attachment of a separate sensing line—if provided
Control Devices:
Strainer: Model 5F-2
Pilot: Model 30AWR
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Ross Valve

Double Acting Altitude Valve, 40DAWR

Sizes: 4-48
Type: Nonthrottling
Primarily Controlled By: Hydraulic pressure
Located: In line between distribution (supply/user) and storage
Purpose: To prevent exceeding a maximum preset storage pressure/Let water flow through the same line from storage to user
Band: Fixed within 9-4
Inlet Pressure: Maximum: 300 psi
Inlet Pressure: Minimum: 5 psi
Construction: Body: 4"-36"—Cast iron (semi-steel) with bronze trim
40"-48"—Ductile iron, with bronze/stainless steel trim
Control Devices:
Strainer: Model 5F-2
Pilot: Altitude: Model 40DAWR
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Troy Valve

Mud Valves (or Plug Drain) A-25612RB

Sizes 4-18 bronze and resilient seats are beveled for positive closure.

Recommended for use in lines of low seating or unseating pressures. Regularly furnished with 2 square wrench nut. May be furnished with handwheel, extension stem or extension stem and floor stand when specified. When ordering extension stem state length and give distance from bottom face of flange to top of handwheel or nut, or to base of floor stand.

Stainless Steel Mud Valve

Sizes 4"-12" standard. Special sizes available
All Stainless Steel Construction
Light, Weight, Medium Duty
Resilient-to-Stainless Steel Seating
Rising or Non-rising stem
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Troy Valve

Shear Gates

Iron Body—Class 30 Cast Iron
Bronze Seat & Disc Rings Bronze, B62
Bolt & Nut Bronze, B62

Troy Valve Shear gates are designed to be used in lines of low seating pressure only for filling and emptying tanks, low pressure sludge discharge lines and similar applications.

A-2520-6 Flanged Frame
125 Pound Standard Bolt Pattern
Sizes: 4"-24"
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

Manufacturer Troy Valve

Telescoping Valves

Standard with Floorstand Mounting Bracket (1)
Special gearbox for easier operation
Patented, self-locking, self-braking worm gear
Stainless steel or PVC slip tubes
Less maintenance, greater durability

Standard with Floorstand (2)
Rack and pinion gearbox
Increased mechanical advantage for easier operation
Stainless steel suspension rod & bail
Improved wiper gasket design
Safer for personel to operate

Offset Standard (3)
Click for detailed product information, or email Craig Moore , phone 716-667-0714.

See products from manufacturers we represent

AUMA Actuators Bristol Babcock Canbar Crispin EFI, Engineered Fluid, Inc. Fresno Valves

Hendrick Screen Co. Henry Pratt Company Hydro Gate Lancaster Tanks Steel Products Onyx Valve Orbinox

Purafil Primary Flow Signal, Inc. Roberts Filter Group Ross Valve Sorensen Systems Steel-Fab

Tenessee Metal Fabricating Trident Actuators Troy Valve Urecon Pre-insulation Pipe Vulcan Whipps, Inc.